Open your doors and look, take your grill off the top of the machine to move it. Some units are screwed into the wall by the frame, some have no screws at all. If you can't locate this or if you have located it and can not turn it off due to age of the valve, shut off the whole house water supply while you move the machine. 90% of the time it will be located below the unit in the basement, or underneath a nearby sink. You must find the water shut off for your refrigerator. It is located underneath your fridge and it connects to your refrigerator solenoid valve. If you have an ice-maker or water dispenser, you have a water line. Step One: Find and shut off your water line. A drill with a 3/8 and 1/4 inch screwdriver bit.Flathead screwdriver or 1/4 ratcheting wrench for moving the leveling legs.The Sub-Zero will roll right over this and protect even the softest floors. Masonite or hardboard to protect your floor.So instead of calling the appliance guy, who tells you to call the contractor, who tells you to call the plumber, who tells you to call the electrician, watch this video. There is a water line for your ice-maker underneath your fridge.They think they are going to scratch your floor.How many of you are here because you need to move your Sub-Zero refrigerator and your contractor, appliance guy, electrician and plumber are all pointing the finger at each other? Everyone is scared to move a Sub-Zero fridge. Then, install the screws.We are not appliance installers. You can now drill pilot holes into the door where your screws will go. Hold the Kick Plate against the door within your marked area and hold in place using masking tape. Using your tape measure and pencil, mark the position of where the kick plate will go on the door. How do you put a kick plate on a wooden door? After you have the kick plate in place and properly aligned, you can place screws into the inner holes and then replace the tacks with screws last. Use tacks lightly stuck through the corner holes of your kick plate in order to align it properly. They're roughly 25-40cm tall and incredibly easy to install. This is normally why they're found on external doors of warehouses, shops, public buildings etc. You need to decide which doors are going to benefit the most from this. Which side of a door do kick plates go on?īottom Kick plates are installed at the bottom of the door. Their main purpose is to protect the surface and material of a door, as they are often kicked open and damage can build up over time. Kick plates are a very common part of door hardware and are installed in most commercial buildings where there is a high amount of traffic going through a door. What is the purpose of a kick plate on a door? Kick plates are installed at the bottom of the door. This keeps the door from interfering with the weatherstripping on the sides of the door jam and the underlying door sweep and sill. The kick plate should be installed 1" above the bottom edge of the door and approximately 2" less in width than the door. A common size of kick plate is 10″ x 34″ for 3'0″ wide doors. Kick plates are usually anywhere from 8 to 24 inches tall and 22 to 48 inches wide. These are generally recommended for doors subject to typical use but especially for openings with closers installed. The term kick plate comes from the fact that when people's hands are occupied they often kick the bottom of the door to open it. They're installed on the push side of the door. Kick plates are an addition to the bottom of your door that help reduce the amount of damage and stress that your door takes over time. It is important to have the plate properly aligned and located the first time you attach the kick plate. Kick plates are generally installed on the lower section of your door in order to protect it from damage from people passing through the entryway.Īdhesive: Mounting with adhesive is a great option for a semi-permanent fixture. Where should a door kick plate be placed? You can install kick plates on both sides of the door if you wish, and enjoy the custom look and protection whether inside or outside. For a standard-sized door, a 6" Kick Plate will suffice, but if you have a larger sized door, you should consider something taller like an 8" Kick Plate. But as mentioned before, this can be down to personal preference. How high should a kick plate be? Kick Plates are traditionally 6" or 8" in height. If your door opens the opposite way to what is standard, or is a swinging door, you may want to fix your kick plate to the inside of the door as well. Kick plates are incredibly easy to use and can be installed inside and out – although, they're usually installed outside.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |